Delaney-Logo
Delaney-Logo
Delaney-Logo
A part that fails inspection is not just a quality problem. It can delay production, disrupt deliveries, and create uncertainty about whether the cause is the resin, the molding process, the tool, or the part design. Most defects offer clues. Their location, appearance, and consistency across cavities can help narrow the cause. Use the checks below as a practical starting point, then confirm changes against the resin supplier’s processing guidance and the part’s approved requirements.

1. Short shots

Molded plastic samples showing incomplete fill, flash, and sink marks on an inspection bench What it looks like: A portion of the part is missing, often at a thin wall, rib, corner, or the end of a long flow path. Common causes: The shot may be too small, or injection speed, pressure, melt temperature, or mold temperature may be too low. Trapped air, restricted gates, or a thin wall relative to flow length can also prevent complete filling. How to investigate: Confirm the shot size and transfer point, then review fill speed and pressure within the approved process range. Check that material is being supplied consistently. If the defect repeatedly occurs at the same last-to-fill location, inspect the venting and gate or runner for restriction. Increasing pressure is not a reliable fix if the root cause is poor venting or a design that is difficult to fill.

2. Flash

What it looks like: A thin film or fin of plastic extends beyond the part, commonly at the parting line, around ejector pins, or near vents. Common causes: The mold may not be closing cleanly because of debris, wear, or misalignment. Excessive packing, low melt viscosity, or insufficient clamp force for the projected part area may also contribute. How to investigate: Check for contamination on the mold’s shutoff surfaces and compare the issue across cavities. Review pack pressure and the fill-to-pack transfer point. If flash continues after the process is stable and the mold is clean, inspect for worn or damaged shutoffs. Persistent tool wear needs a tooling correction, not repeated process adjustments.

3. Sink marks

What it looks like: Shallow depressions on the surface, often opposite a thick wall, rib, or boss. Common causes: The outer surface cools while thicker material underneath continues to shrink. Insufficient packing, early gate freeze, uneven wall thickness, or an overly thick rib can make the mark more visible. How to investigate: Compare the defect location with the part’s thick sections. Check whether packing pressure and hold time are adequate for the gate and resin. If the gate freezes before packing can compensate for shrinkage, adjusting hold time alone may not solve the issue. Consider a design review to core out thick areas and keep ribs proportionate to the nominal wall. Toray’s molding defects and countermeasures guide also outlines common sink causes and remedies.

4. Warpage

What it looks like: A part bows, twists, or cups after ejection or as it cools. Common causes: Uneven cooling, inconsistent wall thickness, different shrinkage through the part, or ejection before the part is sufficiently stable. Material choice and fiber orientation can also influence how a part moves. How to investigate: Confirm that cooling is balanced and that the part is not being ejected too warm. Compare dimensions after a consistent cooling and conditioning period. If the same distortion recurs in the same location, examine wall transitions, gate location, and cooling layout. A process adjustment may reduce warpage, but persistent movement can require a design or tool change.

5. Weld lines

Quality technician examining molded plaques for warpage, weld lines, burn marks, and silver streaking What it looks like: A visible seam where two melt fronts meet, often behind a hole, boss, or other obstruction. Common causes: The fronts may meet too cool to fuse well. Low melt or mold temperature, slow filling, trapped air, and gate placement can all affect the line. In reinforced materials, fiber orientation can also reduce strength at the weld. How to investigate: Identify where the fronts meet and whether the line is cosmetic, structural, or both. Review fill conditions and venting at the meeting point. If the line remains in an unacceptable location, evaluate gate placement or part geometry. Process changes may improve appearance, but they do not always eliminate a weld line or restore strength to a critical location.

6. Burn marks and dieseling

What it looks like: Brown or black discoloration, often at the end of the flow path, near a deep rib, or in a trapped-air area. Common causes: Air trapped in the cavity can be compressed and heated as the melt advances. A phenomenon commonly called dieseling. Blocked or inadequate vents, excessive fill speed near the end of fill, and excessive melt temperature may contribute. How to investigate: Inspect and clean vents, especially where the burn appears. Review the fill profile and check temperature controls. If the mark returns in the same location after routine cleaning, the tool may need additional or improved venting.

7. Silver streaking from moisture

What it looks like: Silvery or whitish streaks on the surface, often following the direction of flow or appearing near the gate. Common causes: Moisture in hygroscopic resins can turn to vapor during processing and leave streaks. Excessive shear, long residence time, contamination, or other trapped gases can produce similar symptoms. How to investigate: Check the resin’s drying requirements and verify that the dryer and material handling process meet them. A drying log alone may not confirm the resin is dry enough; use an appropriate moisture check when required. If drying is within specification, review material history, residence time, and processing conditions. Avoid raising temperatures without checking the material supplier’s limits.

8. Dimensional drift

What it looks like: Dimensions gradually move out of tolerance or vary from shot to shot, even when the parts appear visually acceptable. Common causes: Variation in shot size, packing, melt temperature, cooling, material lot, or machine performance can affect dimensions. Measurement technique and the time between molding and inspection can also influence results. How to investigate: Confirm the measurement method, datum scheme, and conditioning time first. Compare measurements across cavities and production time. Review the process record for changes in cushion, temperatures, transfer point, or hold conditions. If the variation is cyclical or appears across all cavities, investigate process stability; if it is limited to one cavity, inspect that cavity and its cooling or venting.

9. Color variation

What it looks like: Parts differ in shade from one another, or show streaks or uneven color within the same part. Common causes: Inconsistent colorant dosing or mixing, resin or pigment lot variation, contamination during a color change, and changes in temperature or residence time can all affect color. How to investigate: Compare the resin and colorant lots with the approved reference. Verify the dosing system and mixing method, then check for residual material from a previous color. Use consistent lighting and viewing conditions when comparing samples. Agree on an approved color standard and inspection method rather than relying on visual memory.

10. Ejection and scratch damage

Engineer measuring a molded plastic component with calipers during a quality inspection What it looks like: Scratches, drag lines, white stress marks, dents, or visible ejector-pin marks after the part leaves the mold. Common causes: Insufficient draft, a rough or damaged core surface, uneven ejection, inadequate cooling, or excessive packing can make a part grip the mold. Deep features can also create a vacuum effect that resists release. How to investigate: Check whether damage occurs in the same area and whether it aligns with a mold surface or ejector. Review cooling time and ejection balance. If adjustments do not resolve the issue, evaluate draft, surface finish, pin placement, and other tool features.

A systematic way to find the cause

Troubleshooting is more effective when changes are controlled and documented. Start by recording the defect, cavity number, affected dimensions, material lot, process settings, and recent changes. Then investigate in order:
  1. Check material and drying. Confirm the resin grade, lot, handling, and drying requirements. Check colorant or regrind use if applicable.
  2. Review process settings. Compare the current setup with the last approved run. Examine temperatures, fill and pack conditions, transfer point, cooling, and shot consistency.
  3. Inspect the mold. Look for blocked vents, debris, wear, damage, cooling issues, and cavity-specific differences.
  4. Assess the design. If the defect persists within a stable process and sound mold condition, review wall thickness, ribs, draft, gate placement, and flow length.
Change one variable at a time where practical, allow the process to stabilize, and document the result. For broader background on common defect mechanisms, see Toray’s technical troubleshooting reference.

Prevent repeat failures with clear standards

A documented process window records the approved range for critical settings and the conditions under which conforming parts were produced. It gives production and quality teams a shared baseline for setup, troubleshooting, and change control. An approved first-article sample provides a physical reference for appearance and workmanship. Pair it with agreed dimensional requirements, inspection methods, and records that identify the material and process used. Together, these controls make it easier to distinguish a one-time deviation from a recurring process or tooling issue.

When the fix requires a design or tool change

Not every defect can be solved by adjusting the machine. A thin feature that will not fill reliably, an inaccessible trapped-air pocket, a thick section that keeps sinking, or a weld line in a critical load path may require changes to the part or mold. Before authorizing a tool change, confirm the failure mode, review the process evidence, and assess the impact on fit, function, appearance, and cost. Delaney Manufacturing Services supports plastic injection molding, tooling, and mold management, including production with existing molds. If a quality issue points to a process, mold, or design concern, our team can help evaluate the next step. Learn about our injection molding process, mold support, and plastic materials, or contact us about your project. Our custom injection molding services support both short runs and higher-volume production.
Images for illustrative purposes.